+
  • 图片1(1784246860248).png

Application of Impedance Measurement Instruments in Ultrasonic Horns

Summary: This technical document systematically describes the engineering application of impedance measurement instruments throughout the full lifecycle of ultrasonic horns. Starting from the piezoelectric effect and the BVD equivalent circuit model, the document establishes the correlation between impedance parameters (resonant frequency Fs, dynamic resistance R1, mechanical quality factor Qm, electromechanical coupling coefficient Keff, etc.) and the physical state of the horn. It covers four key stages: design validation, manufacturing inspection (from ceramic element incoming screening to finished product testing), assembly and tuning (admittance circle analysis for parasitic vibration evaluation), and online maintenance (frequency drift early warning and failure diagnosis). The document also provides standardized test procedures and practical case studies for 20 kHz and 40 kHz horns, with the aim of elevating horn evaluation from empirical tuning to scientific measurement.

Keywords:

Application of Impedance Measurement Instruments in Ultrasonic Horns


Product Inquiry Download

Application of Impedance Measurement Instruments in Ultrasonic Horns

Theory and Engineering Technical Document

I. Introduction

1.1 The Relationship Between Ultrasonic Horns and Impedance Measurement

1.1.1 The Nature of Ultrasonic Horns as Resonant Systems

An ultrasonic horn is essentially a half-wavelength resonator with length L = λ/2 = c/(2f). The horn-transducer-booster assembly forms a complete electromechanical coupled vibration system, whose electrical port characteristics can be fully described by impedance Z = R + jX. When the system is in resonance, the reactance component X approaches zero, maximizing the conversion efficiency of electrical energy into mechanical vibration energy.

Figure 1-1 Schematic diagram of ultrasonic horn-transducer system

1.1.2 Critical Role of Impedance Measurement Throughout the Horn Lifecycle

Nine out of ten horn problems can be identified from the impedance curve. Impedance measurement spans the entire lifecycle of the horn — from design validation, raw material inspection, in-process manufacturing testing, final product correction, assembly and tuning, to field maintenance.

Lifecycle Stage

Key Parameters

Typical Acceptance Criteria

Design Validation

Fs,  Fp, R1, Qm

Measured Fs deviation from design < ±0.5%

Raw Material Inspection

C0, tan δ, Admittance Circle

Single admittance circle, no parasitic circles

In-Process Manufacturing

Fs, Zmin

Batch frequency deviation < ±0.3%

Final Product Correction

Fs, Fp, Qm, Keff

Qm > 500, Keff > 0.35

Assembly & Tuning

Fs (system), Admittance Circle

Symmetrical admittance circle, no distortion

Field Maintenance

Fs drift, R1 change rate

Frequency drift > 0.5% requires inspection

1.1.3 Technical Evolution from Traditional Empirical Tuning to Scientific Impedance Testing

Traditional methods relied on subjective means such as tapping and listening or Lissajous figures, with poor repeatability. Modern digital impedance analyzers are based on vector voltage-current detection principles, enabling quantitative measurement of complex impedance trajectories and elevating horn evaluation from "craftsmanship" to "science."

Figure 1-2 Comparison of traditional tuning methods and modern impedance testing

Figure 1-3 Modern ultrasonic system test setup

1.2 Overview of Impedance Measurement Instrument Development

1.2.1 Early Impedance Measurement Methods: Bridge method and Q-meter method — cumbersome operation, unable to perform automatic frequency sweeps, and no phase information.

1.2.2 Modern Digital Impedance Analyzers: Employ auto-balancing bridge or RF I-V technology, OFFering advantages such as vector measurement, high-speed sweeping, wide dynamic range, and equivalent circuit parameter extraction.

1.2.3 Domestic and International Instruments: Imported instruments represented by Keysight and Wayne Kerr; domestic specialized instruments represented by Zhixin Precision's ZX70A/ZX80A series and Hangzhou Chenggong Ultrasonic's PV520A series.

Figure 1-4 ZX70A/ZX80A Series Impedance Analyzer appearance

 

II. Equivalent Circuit Model of Piezoelectric Transducers and Ultrasonic Horns

2.1 Fundamentals of Piezoelectric Effect and Electromechanical Coupling

2.1.1 Direct/Inverse Piezoelectric Effect: The piezoelectric effect is a reversible physical phenomenon where mechanical stress produces polarization charge (direct effect) and an applied electric field produces mechanical strain (inverse effect). PZT piezoelectric ceramics are most commonly used in industry.

Figure 2-1 Schematic diagram of piezoelectric effect

2.1.2 Electromechanical Coupling Coefficient: k2 = Wmech/Wtotal, Keff describes the conversion efficiency for the actual vibration mode.

2.1.3 Energy Transfer Chain: Signal generator → Transducer (inverse piezoelectric effect) → Booster → Horn → Workpiece.

2.2 Butterworth-Van Dyke (BVD) Equivalent Circuit Model

2.2.1 BVD Model Structure: Static capacitance C0 in parallel with the dynamic branch (L1-C1-R1 in series). Impedance function Z(ω) = 1 / [jωC0 + 1/(R1 + jωL1 + 1/(jωC1))].

Figure 2-2 BVD equivalent circuit model diagram

2.2.2 Physical Meaning of Dynamic Branch: L1 represents inertia, C1 represents elastic compliance, R1 represents mechanical losses.

2.2.3 Static Capacitance C0: Clamped capacitance, C0 = εA/t.

2.2.4 Limitations of the BVD Model: Lumped-parameter approximation, strictly valid only near the resonant frequency of a single vibration mode.

Equivalent Parameter

Symbol

Physical Meaning

Static Capacitance

C0

Clamped capacitance, determined by dielectric constant, electrode area, and thickness

Dynamic Inductance

L1

Equivalent inertia of the vibration system, L1 ∝ m

Dynamic Capacitance

C1

Equivalent elasticity of the vibration system, C1 ∝ 1/k

Dynamic Resistance

R1

Mechanical losses and load damping

Resonant Frequency

fs

Dynamic branch series resonance, fs = 1/(2π√(L1C1))

Anti-Resonant Frequency

fp

Parallel resonance including C0

2.3 Resonance Theory of Horn Systems

2.3.1 Series Resonant Frequency fs: fs = 1/(2π√(L1C1)), minimum impedance, maximum amplitude.

2.3.2 Parallel Resonant Frequency fp: fp ≈ 1/(2π√(L1·C1C0/(C1+C0))), maximum impedance.

2.3.3 Electromechanical Coupling Coefficient: Keff2 = (fp2 - fs2) / fp2

2.3.4 Mechanical Quality Factor: Qm = fs/(F2 - F1) = 2πfsL1/R1

2.4 Impedance-Frequency Characteristic Curves

2.4.1 Impedance Magnitude-Frequency Characteristics: Minimum impedance at fs (|Z|min ≈ R1), maximum impedance at fp.

2.4.2 Impedance Phase-Frequency Characteristics: θ = 0° (purely resistive) at fs, zero-crossing again at fp.

Figure 2-3 Phase angle vs. frequency curve

2.4.3 Admittance-Frequency Characteristics: Admittance Y = 1/Z = G + jB, the admittance trajectory near fs forms the admittance circle.

Figure 2-4 Admittance circle diagram

 

III. ZX70A/ZX80A Series Impedance Measurement Instruments

3.1 Product Overview and Positioning

The ZX70A/ZX80A series, launched by Changzhou Zhixin Precision Electronics Co., Ltd., is optimized for impedance characterization of piezoelectric devices. The core differentiating feature is the built-in sweep display function on the instrument, eliminating the need for an external computer. It uses vector measurement principles and covers the 20 Hz to 5 MHz frequency range.

Figure 3-1 ZX70A Impedance Analyzer front panel

3.2 Key Technical Specifications

Specification

ZX70A-200k

ZX70A-500k

ZX70A-1M

ZX80A-2M

ZX80A-5M

Frequency Range

20 Hz to 200 kHz

20 Hz to 500 kHz

20 Hz to 1 MHz

20 Hz to 2 MHz

20 Hz to 5 MHz

Basic Accuracy

0.05%

0.10%

Impedance Range

0.01 mΩ to 99.99 MΩ

Equivalent 400-point Sweep Speed

Approx. 4 seconds/unit

3.3 Measurement Functions and Measurable Parameters

Measurable parameters include: resonance characteristic parameters (Fs, Fp, F1, F2), equivalent circuit parameters (R1, L1, C1, C0), quality factor and coupling coefficients (Qm, Keff, Kp, Kt), and impedance extrema (Zmax, Zmin).

Figure 3-2 Zhixin PC software interface with admittance circle plot

3.4 Key Features

3.4.1 Direct Display of Sweep Curves on Instrument: "PC-free" standalone operation, real-time plotting of four coordinate curve types: R-X, Z-θ, Y-θ, G-B.

3.4.2 Real-Time Admittance Circle Plotting: Supports direct admittance circle plotting on the instrument for single-circle verification and multi-circle anomaly identification.

Figure 3-3 Admittance circle principle and parasitic resonance identification

3.4.3 USB Data Export and PC Software: USB HOST port for one-click copying of screen images and CSV data; PC software for detailed analysis and SPC statistics.

3.4.4 Upper/Lower Limit Judgment and Production Line Automation: Built-in upper/lower limit judgment, HANDLER Interface supports PASS/FAIL signal output for direct integration with sorters.

 

IV. Admittance Circle Analysis and Resonance Parameter Identification

4.1 Fundamentals of the Admittance Circle

4.1.1 Admittance Complex Plane: Y = G + jB, horizontal axis is conductance G, vertical axis is susceptance B.

4.1.2 Admittance Circle of an Ideal Piezoelectric Device: Circle diameter D = (C1/C0)·ωs = Keff2·ωsC0.

4.1.3 Relationship Between Admittance Circle and BVD Parameters: R1 = 1/D, the circle diameter directly determines the resonant resistance.

Figure 4-1 Admittance circle diagram

4.2 Admittance Circle Characteristics of Normal Devices

4.2.1 Single-Circle Characteristic: Normal devices exhibit a clear, complete single circular trajectory.

Figure 4-2 ZX70A/ZX80A companion software screenshot

4.2.2 Key Parameter Reading: fs corresponds to the maximum admittance point, fp corresponds to the minimum admittance point. Qm = fs/(f2-f1).

4.3 Diagnosis of Abnormal Admittance Circles

Admittance Circle Characteristic

Geometric Manifestation

Possible Causes

Diagnostic Recommendations

Normal Single Circle

Single complete circle

Good working condition

Parameters pass, ready for installation

Parasitic Circle Superposition

Small circles around main circle

Ceramic delamination/cracks, non-uniform assembly

Ultrasonic inspection, torque check

Elliptical Deformation

Aspect ratio >1.1

Material nonlinearity, temperature gradient

Reduce level and re-measure

Overall Circle Shift

Circle center deviates from expected region

Excessive contact resistance, cable parasitics

Clean fixture, perform correction

  Open Circle
  Arc gap or separated endpoints
  Insufficient sweep frequency range, device has strong damping region
  Expand sweep frequency range, check mechanical damping
 

V. Application of Impedance Measurement in the Horn Design Phase

5.1 Design Validation and Simulation Comparison

5.1.1 FEA Simulation Validation: Simulation-measurement deviation δf = |fFEA - fmeas| / fmeas × 100%, should be controlled within ±1%.

Figure 5-1 FEA simulation mode shape vs. measured comparison

5.1.2 Comparison of Different Horn Materials: Ti-6Al-4V (Qm≈2850) is superior to 7075-T6 (≈2150) and D2 tool steel (≈580).

5.1.3 Influence of Geometric Parameters: Amplification ratio affects C1 and R1; radius of curvature affects Qm; overall length determines the fundamental frequency position.

5.2 BVD Parameter Extraction and Material Characterization

5.2.1 Parameter Extraction Method: The ZX70A uses nonlinear least-squares fitting of measured curves to the BVD model to extract Fs, Fp, R1, L1, C1, C0, Qm, and Keff.

5.2.2 Material Parameter Evaluation: d33 ∝ √(C1/C0), ε derived from C0, kp and Keff converted using geometric correction factors.

5.3 Design Optimization Guidance

5.3.1 Qm for Loss Evaluation: The complete acoustic stack Qm should be ≥1000; too high (>3000) indicates excessively narrow bandwidth.

5.3.2 Keff for Conversion Efficiency: Typical values 35%-50%; approaching the theoretical limit leaves little room for optimization.

5.3.3 Impedance Matching Design: A matching network transforms the transducer's complex impedance to the power supply's optimal load, improving power transfer efficiency from 60%-70% to over 85%.

 

VI. Application of Impedance Measurement in Horn Manufacturing Inspection

6.1 Incoming Inspection of Piezoelectric Ceramic Elements

Inspection Item

Tolerance Range

Remarks

Fs (Series Resonant Frequency)

Nominal ±0.5%

Same batch range < 1.0%

C0 (Static Capacitance)

Nominal ±10%

Measured at 1 kHz

Qm (Mechanical Quality Factor)

≥500 (PZT-8)

Too low indicates excessive loss

Keff (Electromechanical Coupling Coefficient)

Nominal ±5%

PZT-8 typical value 0.45 to 0.50

Admittance Circle Parasitic Loops

No visible parasitic circles

Parasitic loop radius <15% of main circle acceptable

6.2 Transducer Assembly Inspection

6.2.1 Resonance Parameter Correction: Calibrate Fs, Fp, R1, Qm. For 20 kHz-class high-power transducers, R1 is typically < 10 Ω.

6.2.2 Preload Bolt Tightening Verification: Monitored via the resonant frequency shift method — when Fs stabilizes with increasing torque, the preload is appropriate.

6.2.3 Quality Grade Classification: Grade A (precision welding/medical), Grade B (general industrial ultrasonic), Grade C (cleaning/rough machining).

6.3 Finished Horn Inspection

6.3.1 Resonant Frequency Accuracy: Deviation from design value < ±0.3%.

6.3.2 Indirect Gain Factor Assessment: M ≈ k·√(R1,ref/R1,horn).

6.3.3 Pre-Evaluation of Matching: If the assembled system R1 increase exceeds 30% or Qm drop exceeds 20%, this indicates matching issues.

 

VII. Application of Impedance Measurement in Horn Assembly and Tuning

Figure 7-1 Exploded view of the transducer-booster-horn assembly, showing mechanical connection relationships and assembly interfaces

7.1 Three-Piece Assembly Quality Assessment

7.1.1 Pre-Assembly Independent Testing: Establish impedance baseline archives for each component, recording fs, fp, R1, Qm, and admittance circle images.

7.1.2 Post-Assembly System Testing: Good assembly frequency shift controlled within 0.1%-0.3%; exceeding 0.5% indicates contact interface issues.

7.1.3 Admittance Circle Evaluation: Center shift, circle deformation, and multiple loops correspond to asymmetric stress, parasitic mode coupling, and poor thread engagement, respectively.

Figure 7-2 Admittance circles under different preload conditions, showing the effect of assembly state on admittance circle shape — insufficient tightening causes distortion and shift, proper tightening restores regularity

7.2 Frequency Matching and Tuning Validation

7.2.1 Resonant Frequency Determination: Sweep method for precise fs determination, frequency step ≤10 Hz.

7.2.2 Fine-Tuning Validation: Grinding the end face increases frequency; adding a shim decreases frequency. "Small steps, multiple passes" strategy, with each grinding step ≤0.05 mm.

7.3 System Performance Correction

7.3.1 Qm Evaluation: Qm = fs/(F2-F1), best practice control within 500 to 1500.

Figure 7-3 Ultrasonic transducer amplitude decay curve and Qm measurement principle — higher Qm means slower amplitude decay and higher system energy storage efficiency

7.3.2 R1 Monitoring: If R1 increases by more than 20% from the initial value, tightening inspection is recommended.

7.3.3 Half-Power Bandwidth: Determines the system's tolerance to frequency drift; bandwidth < 40 Hz (Qm>500) requires an AFC power supply.

 

VIII. Application of Impedance Measurement in Horn Maintenance and Failure Analysis

8.1 Online Condition Monitoring

8.1.1 Daily Inspection: Quick sweep to obtain Fs, Fp, R1, Qm, with visual inspection of admittance circle morphology.

8.1.2 Frequency Drift Early Warning: δf > 0.5% is a yellow alert, > 1.0% is a red alert.

8.1.3 R1 Trend Analysis: Three consecutive inspections showing R1 increase exceeding 15% is considered an abnormal trend.

8.2 Failure Diagnosis

Failure Mode

Fs

R1

Qm

Admittance Circle Morphology

Fatigue Cracks

Slight decrease

Significant increase

Drop >20%

Parasitic circles appear

End Face Wear

Monotonic increase

Gradual decrease

Slight increase

Regular single circle, increasing diameter

Loose Bolt

Significant decrease

Increase

Decrease

Circle shrinks, boundary blurred

8.3 Maintenance Guidance

8.3.1 Maintenance Cycle Optimization: Construct a Health Index (HI) based on Fs, R1, and Qm to implement Condition-Based Maintenance (CBM).

8.3.2 Life Prediction: Exponential degradation model δf(t) = A·eλt + ε, extrapolate to the failure threshold of 1.5%.

8.3.3 Replacement Decision: Frequency drift ≥1.5%, R1 change rate ≥+40%, Qm change rate ≤-35%, or parasitic circle diameter >15% of main circle — replacement when any single criterion is met.

 

IX. Test Method Standardization and Operating Procedures

9.1 Test Environment Requirements

9.1.1 Temperature and Humidity Control: 23±5 °C, humidity <75% RH; precision horns tightened to ±2 °C.

9.1.2 EMI Shielding: Maintain ≥2 m distance from variable frequency drives, use isolation transformer power supply, shielded twisted pair with single-point grounding.

9.1.3 Mechanical Isolation: Soft support principle — place horns on polyurethane foam or silicone pads; flange horns suspended with thin string near the node.

9.2 Standard Test Procedure

9.2.1 Pre-Test Preparation: Power on and warm up ≥30 minutes, perform open/short correction.

9.2.2 Parameter Settings: Frequency Range covering target resonant frequency ±20%, sweep points ≥401, test level 0.5 to 1.0 Vrms.

9.2.3 Sample Connection: Four-Terminal Pair (4TP) architecture, clamp on the metal electrode area with clean, oxidation-free contact surfaces.

9.2.4 Data Recording: Record fs, fp, Rm, C0, Qm, and environmental conditions.

9.3 Accuracy Assurance and Correction

9.3.1 Regular Correction: Send to a metrology institution every 12 months or 500 hours; verify weekly with a "golden sample."

9.3.2 Measurement Uncertainty: Expanded uncertainty for fs Approx. ±0.04%, for Rm Approx. ±9% (k=2).

9.3.3 Cross-Instrument Consistency: Systematic deviation between ZX70A and ZX80A is typically <0.01%, allowing direct equivalent use.

 

X. Typical Application Cases and Practical Guide

10.1 Complete Test Case for a 20 kHz Plastic Welding Horn

Full-chain inspection includes ceramic element screening (C0±2%, tan δ≤0.5%), transducer assembly (fs deviation ≤±0.15%, Qm≥2500), booster matching (impedance transformation ratio ±5%), and horn tuning (final fs deviation ≤±0.05%, R1≤15 Ω, admittance circle roundness deviation ≤8%). Full-chain inspection improves the first-pass yield from 78% to 94%.

10.2 Precision Tuning Case for a 40 kHz Metal Welding Horn

High-frequency horn testing must account for additional mass from fixtures; use soft clamping or vertical suspension. Set the ZX70A to center frequency mode with a 39.8 to 40.2 kHz narrow-band sweep at 1 Hz step. For titanium alloy horns, each 0.10 mm reduction increases frequency by Approx. 35 to 40 Hz. Optimal operating point criteria: R1≤25 Ω, Qm between 1500 to 2500, admittance circle diameter ≥45mS.

10.3 Production Line Batch Inspection Automation Solution

HANDLER Interface Programming: Connect via DB-25 to PLC, PASS/FAIL controls sorting cylinders, supporting up to 9 sorting bins.

SPC Statistical Process Control: Monitor fs and R1 as CTQ metrics with UCL/LCL control limits; after implementing SPC, frequency deviation defect rate dropped from 3.2% to below 0.8%.

Efficiency Optimization: Fast mode single sweep approx. 800 ms; "narrow-band pre-sweep + fine sweep" two-step method; dual-station alternating design achieves a stable 4-second/unit cycle, with daily output of 7,200 units (two-shift operation).

*Disclaimer: This document is for reference only and does not constitute investment or procurement advice. Data is from public sources and may contain delays or errors; please refer to the latest official information.